Mastering Chain Setup:
Singomakers Ableton Mastering Templates Vol 2 'Ableton Mastering Templates Vol 2' was created by the mastering engineer who created tracks and mastering for Axtone, Enormous Tunes, Unreleased Digital, Spinnin', Ultra Music, Mixmash, CR2 Records, Dim Mak, Big & Dirty and a lot more.
Lets set up a powerful
mastering chain in Ableton with the goal of only using built-in audio effects. When “mastering” on this basic level, we are trying to accomplish 3 things:- balance the mix
- clean up resonance
- add loudness (punch) to the track
Of course there are different definitions of mastering and many philosophies on the order of your effects used. For example, one could perfectly argue, that the multiband dynamics should go in front of the Glue compressor.
Chain Layout:
But lets go ahead and lay down our chain as we are using it inside of the video tutorial:
Ableton Mastering Template Free Download Pdf
EQ8: Lowcut - This EQ is operating in mid side mode. We are cutting out frequencies below 100hz on the side and freqs below 35 hz in the mids. That way we have a clean low cut and our bass is operating in mono
Glue compressor: We are catching some of the peaks over the entire frequency range
EQ8: We are flattening out some unwanted resonances
Multiband Dynamics: We are balancing the low, mid and highs with 3-band multiband compression Izotope rx repair assistant greyed out.
Compressor Punch: We are adding punch to the mix, emphasizing the dynamics
Compressor Sustain: We are flattening out the mix a little bit (in order to be able to make the sum louder in the end)
EQ8: Final touches, we are pulling up the bass a bit and adding a little bit of brilliance in the top end
Limiter: We are increasing the loudness of the sum of our track. Note: don’t push it too far, Ableton’s limiter starts distorting the sound quite quickly.
Of course, this chain has its limitations - but we found it a good way to start with a basic master for your Ableton productions. Make sure you adjust the loudness of your mix before entering the chain. If the mix plays at low volumes, add a utility in front of the chain an turn up the level to get the chain compressors working - if its getting too heavy - turn it down a tad.
- Download the free Ableton-only Mastering Chain from ourFreebie section
'The best mastering chain I have ever used man!!!!'
- Youtube Comment by Robert B.
More Info:
Ableton Mastering Template Free Download Powerpoint
- Grab the free Ableton-only Mastering Chain from ourFreebie section
- 5h+ Online MASTERING COURSE (from start to finish)
Ableton Mastering Template Free Download Html
Keywords: Mastering with Izotope Ozone, LUFS vs dbFS, Fab-Filter Saturn, Mastering with Fab-Filter only, Mastering with Ableton only, Fletcher-Munson Curve, Mastering Chain Blueprint
The cloud-based mastering service LANDR provides a convenient way to put those all-important finishing touches on tracks. Far from a one-size-fits-all solution, their mastering system utilizes an adaptive engine that ‘listens’ to music and makes subtle adjustments based on the unique properties of the song.
TL;DR -, take them to.Be clear in your titles. It should be clear what your post is about from the title itself. All post asking a question must end with a question mark. Free ableton packs reddit. No all caps titles.Ableton Help:'s - Updated for 2018, and not just for people learning.
Template Free Download Html
Adapting some of that advanced signal processing know-how, LANDR’s senior audio producer Pheek, in collaboration with Performodule, has assembled the Tone Sculptor devices – three Audio Effects Racks designed to carefully enhance and attenuate key frequency ranges in your mixes. The Low, Mid and High Sculptors are perfect for adding just the right touch of polish, glue, and analog character to your tracks. Further refinements can be achieved by tweaking the intriguingly named “Pixie dust”, “Ouchie”, “Big”, “Nose”, and “Old Skool” controls.
Ableton Mastering Template Free Download Free
Learn more about LANDR